| Item 1: Explosion proof/Intrinsic Safety Type |
| Not specified |
| NF1 |
NEPSI Explosion proof Permit: d Ⅱ CT6 Environmental Temperature: -40-60 ℃ Electrical Interface: 1/2NPT |
| FF1 |
FM Explosion proof Permit C1: I-II&III Div 1&2, Gps. B, C, D, E, F&G NEMA 4X Temperature: C1: T6 |
| FF15 |
FM Explosion proof Permit C1: I-II&III Div 1&2, Gps. B, C, D, E, F&G NEMA 4X Temperature: C1: T6 |
| KF1 |
CENELEC (KEMA) Explosion proof License: EExd Ⅱ CT4, T5, T6 |
| KF5 |
CENELEC (KEMA) Explosion proof License: EExd Ⅱ CT4, T5, T6 |
| CF1 |
CSA Explosion proof License C1: I-II&III Div, 1&2, GPS, B, C, D, E, F,&G ENCL: Type4X Temperature: CI: T4, T5, T6 |
| CF15 |
CSA Explosion proof License C1: I-II&III Div, 1&2, GPS, B, C, D, E, F,&G ENCL: Type4X Temperature: CI: T4, T5, T6 |
| NS1 |
NEPSI intrinsic safety license: ia Ⅱ CT4 environmental temperature: -40-60 ℃ electrical interface: 1/2NPT |
| FS1 |
FM intrinsic safety license intrinsic safety C1: I-II&III Div, 1&2, Gps, B, C, D, E, F,&G non combustible C1: I-II&III Div, 1&2, Gps, B, C, D, E, F&G |
| KS1 |
CENELEC (KEMA) intrinsic safety license: EEx ia Ⅱ CT4 |
| CS1 |
CSA intrinsic safety license: C1: I-II&III Div, 1&2, GPS, A, B, C, D, E, F&G ENCL: Type4X Temperature C1: T4 |
| FU1 |
Including FF1 and FS1 |
| KU1 |
Including KF1.KS1 and N-type KEMA, N-type EX nAII CT4 |
| CU1 |
Including CF1 and CS1 |
| SU1 |
SAA explosion-proof and intrinsic safety and spark free Ex d Ⅱ CT6/T5/T4 IP67, Ex ia Ⅱ CT4 IP67, Ex n Ⅱ CT4 IP67 |
| KS5 |
CENELEC (KEMA) intrinsic safety explosion-proof: [Entity mode]: EEx ia Ⅱ CT4; [Fisco mode]: EEx ia Ⅱ CT4/EEx ia Ⅱ BT4 |
|
| Item 2: Explosion proof sealing joint |
| Not specified |
| G71 |
Connection port: 1/2NPT Applicable cable outer diameter: Φ 8.5 ± 0.5 (1 piece) |
| G72 |
Connection port: 1/2NPT Applicable cable outer diameter: Φ 8.5 ± 0.5 (1 piece) |
| G81 |
Connection port: 1/2NPT Applicable cable outer diameter: Φ 8.5 ± 0.5 (2 pieces) |
| G82 |
Connection port: 1/2NPT Applicable cable outer diameter: Φ 8.5 ± 0.5 (2 pieces) |
|
| Item 3: Painting: Color change or painting change |
| Not specified |
| P1 |
The color change only applies to the transmitter housing Munsell logo code: N1.5, black |
| P2 |
The color change only applies to the transmitter housing Munsell logo code: 7.5BG4/1.5 green |
| P7 |
The color change is only applicable to the silver metal of the transmitter housing |
| X1 |
Paint changes, epoxy resin baking |
|
| Item 4: Lightning Protection Device |
| Not specified |
| A |
Transmitter power supply voltage: 10.5-32V DC (intrinsic safety type: 10.5-30V DC) Maximum allowable current: 6000A (1X4 μ S), repeated 1000A (1X40 μ S) 100 times |
|
| Item 5: Prohibition of oil treatment or prohibition of water and oil treatment |
| Not specified |
| K1 |
Degreasing and cleaning treatment |
| K2 |
Defatting and cleaning treatment, and filling the membrane box with fluorine oil at a temperature of -20-80 ℃ |
| K5 |
Defatting, washing and drying treatment |
| K6 |
Defatting, washing, and drying the membrane box, filling it with fluorine oil, and using it at a temperature of -20-80 ℃ |
|
| Item 6: Calibration Unit |
| Not specified |
| D1 |
P correction (Psi unit) |
| D3 |
Bar calibration (bar unit) |
| D4 |
M correction (kgf/cm2) |
|
| Item 7: Sealing treatment of SUS630 nut |
| Not specified |
| Y |
Surface coating of SUS630 bolts and nuts for fastening chamber flange (liquid silicone rubber) |
|
| Item 8: Long exhaust plug |
| Not specified |
| U |
Total length: 112mm (standard type: 32mm) |
|
| Item 9: Quick Response |
| Not specified |
| F1 |
Refresh time: ≤ 0.125 seconds Response time (including minimum damping time constant): Maximum 0.3-0.5 seconds (L capsule 0.6 seconds) |
|
| Item 10: PID/LM Function |
| Not specified |
| LC1 |
PID control function, Link Master function |
|
| Item 11: Set the output to low when the CPU is abnormal |
| Not specified |
| C1 |
Low side: ≤ -5% (3.2mA DC) |
|
| Item 12: NAMUK NE43 |
| Not specified |
| C2 |
[Output signal 3.8-20.5mA] Fault alarm output -5%, below 3.2mA |
| C3 |
[Output signal 3.8-20.5mA] Fault alarm output 110%, above 21.6mA |
|
| Item 13: Stainless steel amplifier housing |
| Not specified |
| E1 |
Amplifier casing material: SCS14A stainless steel (equivalent to SUS316L cast stainless steel or ASTM CF-8M) |
|
| Item 14: Gold plated film |
| Not specified |
| A1 |
Gold plating on sealing membrane |
|
| Item 15: Configuration |
| Not specified |
| R1 |
User Configuration Software |
|
| Item 16: Container flange options |
| Not specified |
| N1 |
Without exhaust and drain plugs |
| N2 |
N1 and without process joints, both sides of the chamber flange are machined with DIN 19213 7/16 inch × 20 internal threads (installation threads), and the rear side is equipped with a blind plug |
| N3 |
Manufacturing of accessories for N1 and N2 chamber flanges, diaphragms, bodies, and blind plugs |
|
| Item 17: Stainless Steel Tag Plate |
| Not specified |
| N4 |
JIS SUS304 stainless steel tag plate fixed on the transmitter |
|
| Item 18: Accessory Manufacturing Certificate |
| Not specified |
| M01 |
Container flange |
| M11 |
Container flange, process joint |
|
| Item 19: Proof of stress test leakage test |
| Not specified |
| T09 |
M. H membrane box test pressure: 32MPa test fluid: nitrogen retention time of 10 minutes |
|
