VIP member
UQK-17 series dry spring floating ball liquid level controller
The UQK-17 series dry spring floating ball liquid level controller is widely used in civil construction water tanks, water towers, water tanks, as wel
Product details
UQK-17The series of dry spring floating ball liquid level controllers are widely used in civil construction water tanks, water towers, water tanks, as well as open or closed storage tanks and underground tanks in industries such as petrochemicals, papermaking, food, and sewage treatment. The detected medium can be divided into various conductive and non-conductive liquids such as water, oil, acid, alkali, and industrial sewage. This controller can automatically control the liquid level.
Model Description:
|
UQK-17
|
Dry spring floating ball liquid level controller
|
||||
|
|
Measurement points
|
1Indicate measurement point 1, 2 indicates measurement point 2, and so on.
|
|||
|
material
|
B
|
Indicates stainless steel material 1Cr18Ni9Ti (321) or 304
|
|||
|
F
|
For fluoroplastics
|
||||
|
|
Installation method
|
|
|||
|
|
1
|
The installation method is threaded installation
|
|||
|
2
|
The installation method is flange installation
|
||||
|
structural style
(Model)
|
Result
|
Function
|
|
a
|
A normally open dry spring (upper position)
A normally closed dry spring (lower position)
|
Pump on at high water level
Stop the pump at low water level
|
|
b
|
A normally open dry spring (upper position)
A normally closed dry spring (lower position)
|
Pump on at high water level
Stop the pump at low water level
|
|
c
|
A frequently played reed switch (upper position)
A normally closed reed switch (lower position)
|
automatic control
|
|
d
|
Three normally open dry springs
A normally closed dry spring
|
Used for upper and lower liquid level control and high and low limit liquid level alarm
|
|
e
|
A normally open dry spring
Three normally closed dry springs
|
Used for upper and lower liquid level control and high and low limit liquid level alarm
|
|
f
|
Four frequently played reed switches
|
automatic control
|
□Specification
1Measurement range
GType (stainless steel) ≤ 4m, (negotiated for 4m or more)
FType (fluoroplastic) ≤ 4m
2Temperature of the measured medium
Domestic reed switch -10 ℃~+80 ℃, imported reed switch -10 ℃~+100 ℃
3Specific gravity of the tested medium:>0.7g/cm3
4Work pressure: ≤ 1.6MPa
5Capacity of reed switch contacts: 220VAC, 1A
□Working principle
Install several in the controllerGAG-5Type high-power reed switch, when the float ball equipped with magnetic steel moves up and down with the liquid level, the contacts of the reed switch move accordingly, thus achieving the purpose of controlling the liquid level. Fully automatic control of liquid level by drivable pump
□Installation and wiring
1、 flange mountingG- Flange standardHG20592－97DN150、PN1.6(Other flange standards to be negotiated and resolved) Thread installation thread sizeM30×2
2、 The connecting wire between the sensor and the display instrument cannot be laid in the same way as the AC power supply, as the induced AC power may affect the instrument. At the same time, to avoid interference signals, shielded cables should be used as much as possible to be laid inside the iron pipe.
3、 The sensor is installed on the tested container, and its installation method is shown in Figure 2. It is best to fix the lower end of the sensor firmly to the bottom of the container.
4、 Due to limitations in railway transportation, greater than4mThe above is packaged in sections and installed by the user themselves. After welding, the weld seam is filed flat and the water pressure test is conducted (pressure less than)0.6MPa）Only when there is no leakage can it be used,FThe type of sensor also needs to be fitted with a fluoroplastic sleeve that comes with the box and fixed; Or users can solve transportation problems themselves.
□Ordering Instructions
1、 Specify the specifications, models, and quantities of the sensors
2、 Specify the material and measurement point of the sensorL1、L2……L3The specific location and total length of the sensor should be providedL1、L2……
L3Contact form (normally open or normally closed), if uncertain, produce with normally open contacts.
L3Contact form (normally open or normally closed), if uncertain, produce with normally open contacts.
3、 The sensor must be checked before installation, and a multimeter rod should be connected to the sensor terminal. When the float moves up and down, the
Make the reed switch move accordingly.
Make the reed switch move accordingly.
Online inquiry
-
Contacts
-
Company
-
Telephone
-
Email
-
WeChat
-
Verification Code
-
Message Content
-