Product Name: SJ-FH01 Composite Eye Wash

Performance parameters:

Nominal pressure, sealing pressure, working pressure, spray flow rate (L/min), eye wash flow rate (L/min), applicable conditions

0.4MPA 0.45MPA 0.20-0.40MPA 120-180 liters/minute ≥ 12 room temperature pure water or water that meets hygiene standards

structural characteristics
1. Use ball valves to control spraying and eye washing separately. Easy to operate, fast opening and closing, and reliable sealing.
2. The outlet water of the eye washing nozzle is soft foam water flow, which increases the cleaning efficiency by 50% compared with the common eye washing nozzle.

3. EvacuateAntifreeze device, ensuring that the eyewash pipe in the person is emptied within 30 seconds,Super resistant to chemical substances such as acid, alkali, salt, and oil corrosion.

Main materialsFull of 304 stainless steel, with a high gloss polished surface.

Installation and Debugging
1. Before installation, the product model, certificate of conformity, user manual, and packing list must be rechecked.
2. The installation location should be within 15 meters of the accident prone area and within 10 seconds of running speed to reach the flushing area.
3. Installation and Debugging:
a. Connection between the base and the lower half of the riser: Wrap the raw material tape around the thread of the base and tighten the three-way connection with the water outlet.
b. Installation base: Adjust the direction of the three-way drainage outlet according to the position of the drainage pipe, mark the drilling position according to the screw holes on the base, and then set M10 expansion screws or anchor bolts according to the ground level.
c. Install the flushing pipeline: Tighten the flushing nozzle onto the curved horizontal pipe of the nozzle, wrap the other end of the nozzle pipe with raw material tape, and tighten it onto the upper half of the vertical pipe. Adjust the direction so that the flushing nozzle is facing downwards, and then lock the nozzle pipe with the back nut;
d. Connect the upper and lower halves: Place a female pad at the female end and tighten it.
e. Install the eyewash basin: Wrap the raw material tape around the thread of the eyewash basin drain outlet, and connect it to the lower half of the reducing tee and tighten it.
f. Install the dual nozzle eye wash section: Place the G 189 "mesh pad into the G 189" lock nut and connect it to the G 189 "connector
Tighten it.
g. Connect the inlet and outlet pipes, check whether the ball valve switch is flexible and in place, and whether there is any blockage.
h. The eye wash dual nozzle has an eye wash flow control valve in the middle of the two pipes, and the flow rate of the eye wash nozzle is controlled by the flow control valve. It has been debugged before leaving the factory. However, due to differences in water supply pressure and flow rate, it can be readjusted on-site during installation to achieve a flow rate suitable for human eyes. Adjustment method: Unscrew the top protective cap and use a straight screwdriver to adjust the valve stem. Rotate clockwise to reduce the flow rate. Rotate counterclockwise to increase the flow rate.

Instructions for use
Before use, open the inlet control valve first
When pouring, please pull down the pouring switch handle to open the pouring valve (opening angle 90 °), and push up the pouring switch handle to close the pouring valve. (The connecting rod of the ball valve is closed at 45 ° above the ball valve and open at 45 ° below it)
If you need to wash your eyes, please push the eye wash switch push plate clockwise to open the eye wash valve, and pull back the push plate counterclockwise to close the eye wash valve.

Maintenance and Care
1. Emergency use is only allowed in case of accidents. It is strictly prohibited to use it for bathing during normal times. Rules and regulations should be established and inspections should be carried out to prevent violations or the use of it as a regular bathing or hand washing tool, which may cause product failure and unnecessary accidents.
2. Comprehensive testing should be conducted at least once a week to verify the reliability and effectiveness of the equipment, to ensure effective emergency use in the event of an accident, and to provide reliable personal safety and hygiene protection. This product is not a medical device and is only used for emergency shower and to reduce the harm of harmful substances to the human body.
When an accident occurs, the victim must choose the flushing time based on the degree of harm caused by harmful substances. Prepare emergency rescue measures during the period.
Enable optional configurationsPedals can be added, ABS coating and lighting devices can be added, and anti freezing devices for emptying can be added. Customization can be made according to customer requirements.