VIP member
Disc type torque sensor
Brief introduction: The disc torque sensor CKY-806A is the axial length * short form of the CKY-80 series torque coupler The diameter of the flat key
Product details
Details introduction:
Disk type torque signal coupler CKY-806A
1characteristic:
1characteristic:
This series of torque signal couplers is a specially developed signal coupler for transmitting torque parameters based on standard torque strain sensors.
CKY-806A type torque speed coupler isThe axial length * short form of CKY-80 series torque coupler The diameter of the flat key and shaft hole in this form must be customized according to user requirements
This series of torque signal couplers is equipped with:
1. Torque measurement function;
2. Energy and signal non-contact transmission function,
3. Digital output signal function
4. It can transmit static torque signals, rotational torque signals, dynamic torque signals, and static torque signals,
2. Energy and signal non-contact transmission function,
3. Digital output signal function
4. It can transmit static torque signals, rotational torque signals, dynamic torque signals, and static torque signals,
5. The transmission of signals is independent of rotation, speed, and direction.
6. There are no bearings between the stationary shell and the rotating diskCan adapt to long-term, high-speed operation.
7. High precision and good stability;5. Small size, light weight, easy to install;
8. Continuous transmission of forward and reverse torque signals without repeated zeroing;
9. Without wear parts such as collector rings, it can operate at high speed for a long time;
10. Strong anti-interference ability;
11. Can be located at any positionInstall in any direction;
twoTechnical indicators
1. Range:5, 10, 20, 50, 100N... 1 million N · m;
2.Accuracy: 0.5%, 0.25%, 0.1% F · S;
2.Accuracy: 0.5%, 0.25%, 0.1% F · S;
3. Applicable speedBelow 6000 revolutions per minute
4. Environmental temperature: 0 ℃-５0℃
5.Frequency response: 100 μ s
6.Self weight=2.8Kg
5.Frequency response: 100 μ s
6.Self weight=2.8Kg
7. Output signal: 0-12v square wave frequency; Load current<10mA
Zero torque: 10 KHZ ; Positive full-scale: 15KHZ ; Reverse full range: 5 KHZ;
3、 Installation
1．The CKY-806 speed coupler consists of a stationary housing and a rotating disk
2. Place the stationary shell on the outside of the rotating disk according to the positioning color pointsThe positioning color point cannot be reversed!
3. Connect one end of the rotating disk to the power or load through a flange coupling.
4. The stationary shell is fixed on the baseAdjust the gap to ensure that there is no contact between the stationary shell and the rotating disk!
4、 Signal processing
1. Use CKY-80 series torque meter to directly display torque values;
2. Directly send the torque frequency signal to the computer orPLD for processing;
3. Convert to4-20mA or1-5V analog signal.
5、 Usage precautions:
1. The wiring must be correct; 2.Range of ± 15V: not less than ± 14.5V and not more than ± 15.5V;
2. The signal line output must not be groundedShort circuit to power supply, output current not exceeding 10mA;
3. The shielding layer of the shielded cable must be consistent with ±Connect the common terminal (power ground) of the 15V power supply.
4. If you have any questions during use, please contact our company in a timely mannerDuring the warranty period, it is not allowed to disassemble it by oneself.
Online inquiry
-
Contacts
-
Company
-
Telephone
-
Email
-
WeChat
-
Verification Code
-
Message Content
-