Equipment Introduction:

According to national regulations, different testing fixtures are used to conduct performance tests on the product. Tensile and compressive forces are applied to the test sample at a certain speed to obtain the energy of the sample. This machine has a wide range of applications. By replacing different fixtures, it can test the tensile, compressive, bending, tearing, peeling, and shear tensile strength, elongation, adhesive force, tensile stress, elongation, deformation, and adhesion between metal and various materials of metal materials such as steel, copper, brass, plates, bars, square steel, aluminum alloys, cast iron, stainless steel, magnesium alloys, non-metallic plastic products, rubber makers, electronic products, or dumbbell shaped test pieces. It can also achieve comprehensive mechanical testing of multiple closed-loop tests such as constant stress, constant strain, creep, and relaxation.

Main technical parameters of the equipment:

♦ Maximum test force: 100KG

♦ Accuracy level: Level 0.5

♦ Test force measurement range: 0.2%~100% FS

♦ Relative error of test force indication: within ± 0.5% of indication

♦ Test power resolution: 1/300000 of the maximum test power (with constant resolution throughout the entire process)

♦ Deformation measurement range: 0.2~100% FS

♦ Relative error of deformation indication: within ± 0.50% of the indication

♦ Deformation resolution: 1/300000

♦ Relative error of displacement indication: within ± 0.5% of the indication

♦ Displacement resolution: 0.025 µ m

♦ Force control rate adjustment range: 0.005~5% FS/S

♦ Relative error of force control rate: within ± 1% of the set value

♦ Deformation rate adjustment range: 0.02~5% FS/S

♦ Relative error of deformation control rate: within ± 2% of the set value when the rate is less than 0.05% FS; When the rate is ≥ 0.05% FS, it is within the set value of ± 0.5%

♦ Beam speed adjustment range: 0.001~500mm/min

♦ Relative error of crossbeam speed: within ± 1.0% of the set value when the speed is less than 0.01mm/min; When the speed is ≥ 0.01mm/min, within ± 0.2% of the set value

♦ Constant force, constant deformation, constant displacement control range: 0.5%~100% FS

♦ Constant force, constant deformation, and constant displacement control accuracy: within ± 0.1% of the set value when the set value is ≥ 10% FS; When the set value is less than 10% FS, within ± 1% of the set value

♦ Effective stretching space (including fixtures): 1000mm

♦ Effective test width: can be extended left and right

♦ Power supply: 220V 50HZ 10A

♦ Maximum capacity protection, this machine is designed to protect the computer system and prevent the load from exceeding its safe capacity. Different safe capacities can be set, and when the set capacity is reached, it can automatically shut down to protect the load element

♦ Sensor (Load Element): A brand that strives to promote the use of high-tech products

♦ Discontinuous shutdown: When testing a breakpoint or damage, the motor automatically stops braking without the need to press the stop button again, protecting the machine

♦ Dust cover: The lead screw is equipped with a dust-proof device to prevent flying dust and test objects from entering the lead screw, increasing the lifespan and accuracy of the instrument, and improving its appearance

♦ Upper and lower limit micro motion device: When the upper horizontal bar reaches the highest and lowest points, the micro switch automatically turns off the power to protect the load element and motor, which can avoid damage to the instrument caused by improper use by the operator

♦ Warranty: One year of free after-sales service and long-term after-sales service

♦ Motor: 1HP servo motor (International card)

♦ Transmission: Drive the pot wheel and pot rod with a speed reducer, which has low noise and high durability